Durable Air Control Tipping Valve HYVA 14750665H 14750667H

Durable Air Control Tipping Valve HYVA 14750665H 14750667H

Description:
part no. description qty
147 50 665 H control pneumatic - 1 - TF/LF 1
147 50 667 H control pneumatic - 1 - TS/LF 1

Explanation of codes:
1 = control has 1 section
TF = lever is fixed in tipping end position
TS = lever has a spring return in tip position
LF = lever is fixed in lowering end position
Drawings


1 : = air inlet
3 : = air exhaust
21 : = lowering connection

(to tipping valve)
22 : = tipping connection

(to tipping valve)

Mounting of the air control:

When the air control is mounted next to the drivers seat a strong support should be used.
Available supports are:
- 092 32 002 for on-seat mounting
- 092 05 002 for on-floor mounting
Use always rubber grommets to protect air tubes and to prevent that dust and water enters the cabin.
For trouble free life of the entire pneumatic system the air system must be free from water.
The air control should be mounted in such a way that:
1 it is easy to reach by the operator.
2 it is no obstacle when entering or leaving the cabin.
3 it is clear from any moving parts such as drivers seat and closed door.
The air exhaust connection must be brought outside the
cabin to prevent air entering the cabin, which gives the following disadvantages:
1 noise
2 blown up sand and dust
3 when alcohol is used to prevent the pneumatic system against frost the alcohol vapour will enter the cabin
o Make sure that air tubes:
1 are not too close to sharp objects.
2 are clear from moving parts.
3 are clear from exhaust and compressor lines.
4 can not get kinked.
5 are not too long.
note: The air supply must always be tapped off from a accessory air tank or auxiliary valve and the
pneumatic system must be protected with a charging valve.
( see guide - lines from truck manufacturer )
For operation of the air control see the Hyva
operation and maintenance instructions’

Note:
The air supply must always be taken from an accessory air tank or auxiliary valveand the pneumatic system must be protected with a charging valve.

pos. part no. description qty.

1 147 50 665 H control pneumatic - 1 - TF/LF 1

147 50 667 H control pneumatic - 1 - TS/LF 1

2,3,4,5 147 52 141 K air kit valve 1

2 148 10 517 coupling for air control G1/8” 3

3 148 10 515 coupling for air control M5 1

4 148 75 500 air tube tie 4

5 148 75 007 air tube 6x4 ( 20 m ) 1

6,7,8 147 54 010 charging valve kit optional 1

7 148 84 501 washer 27x22 optional 1

8 148 11 005 coupling m 22-6 mm optional 1

092 32 002 mounting support optional 1

092 05 002 mounting sup. (angled) optional 1



Competitive Advantage:

Quality Standards :

The company for the products are brand new original products, no second-hand and refurbished products, or leave a compensable ten and return the full amount , but the buyer due to our purchase of model error is not responsible for returns, another of the company's sales of products enjoy one year from the date of shipment quality assurance , according to the original quality standards , during warranty with product problems , need confirmation testing by the manufacturer , the supplier to be solved , the demand side due to storage , use, poor maintenance caused by lower-quality product , and not raise objections

Warranty:

All item Comes with Basic 3 Month Sellers Warranty, if item defective in 3 Month, We will offer replacement without extra Charger(including shipping fee)After we Receive the Defective item.
If item Defective after 3 Month, Buyers can still send it back, We will contact suppliers or Manufactory for Warranty. Buyers Might Need to pay the Shipping fee For resend the replaced item.